 |
Model Links |
|
|
| PAGE
1 |
 |
SMBC IC-Gel™
IC-GEL is an excellent putty for
plastic models. It will fill any void and can be formed to many shapes.
Applying INSTA-SET™ allows IC-GEL™ to be sanded or filed to final shape in
less than 20 seconds. Autobody repairmen have finished their jobs in a
fraction of the time by using IC-GEL™ with the additional advantage over
normal body putties of superior bonding to metal surfaces. IC-GEL™, along
with MAXI-CURE™, is also used for the underwater bonding of coral to rock.
|
| 7 oz. Tube |
Price $4.95 |
|
|
| |
|
 |
SMBC INSTA-CURE+™
is a higher viscosity CA for loose fitting joints in which
the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then
the parts are held tightly together for about 5 to 15 seconds. For large surface areas,
including those with close fitting joints such as laminations, INSTA-CURE+ ™ should
also be used. To prevent premature curing, don’t spread the glue into a thin film.
Lay down a serpentine bead with about 1" separations on one surface, then assemble
the parts, letting the pressure spread the CA out. |
| |
|
| 1/2 oz. Bottle |
Price $3.50 |
|
|
"Recommend By Chris" |
SMBC MAXI-CURE™
extra thick CA is the best CA for most plastics, including
GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used
with INSTA-SET™, it works better than any putty for modifying or filling voids. It
can be carved with a knife or razor blade and sanded and feathered to form a finish
indistinguishable from plastic.
MAXI-CURE™
bonds fiberglass, hardwood, metal and rubber better than any other hobby
adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area
to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any
other adhesive. It also is best for bonding the tires for R/C cars. |
| 1/2 oz. Bottle |
Price $3.95 |
|
|
  |
SMBC INSTA-SET ™
is a catalyst which acts as an accelerator that allows CAs
to quickly cure in thick layers by enhancing the alkaline conditions during
polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that
flows from joints when parts are pressed together. Applying an additional bead of thick CA
along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s
strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface
and CA to the opposite surface. When brought together, they will bond instantly.
INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds
without any degrading of the CAs strength, which can occur with many other accelerators.
It is compatible with all surfaces, even clear plastic and white foam.
|
| 2 oz. Pump Spray |
Price $4.99 |
|
|
| 8 oz. Refill |
Price $10.99 |
|
|
 |
SMBC UN-CURE™
debonder will soften cured CA. If parts are bonded
incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will
dissolve the CA in about a minute. Apply on bonded skin and roll apart
fingers. Once unstuck, use acetone to clean off softened CA, then wash off
with soap and water. |
| 1 oz. Bottle |
Price $3.95 |
|
|
| RETURN TO MAIN PAGE |
|
|
|
|
